How Do You Know if a Brake Caliper Has Gone Bad?
The most important safety feature on your car: the brakes. Surely you can survive if your ride won’t go from zero to sixty in less than six seconds. But if you can’t stop… well now, that’s a problem. Most likely, your car is equipped with highly efficient two- or four-wheel disc brakes. But your braking system needs attention – periodic maintenance to remain in good working order. Under the best circumstances, your brakes will wear out eventually. Unfortunately, brake systems sometimes (wait for it…) break down. Other times, they are just plain abused and neglected. Brake pads are worn too thin. Brake rotors become grooved or warped. And dirt, grime, salt, and sand can cause your calipers to seize up.
You might already know that your brake pads need to be replaced regularly. You might suspect that your rotors will eventually wear too thin to be of use and will need replacement. But did you know that your brake calipers can go bad? Let’s take a look at what a brake caliper is and how you might detect that is has gone bad.
What is a Caliper?
A disc brake system is made up of several components. Attached to each wheel are a brake rotor (the disc part), a pair of brake pads, and a brake caliper. The caliper is a clamp of sorts. It suspends the brake pads in a sandwich configuration on each side of the flat, round rotor (disc). When the wheel spins, the rotor spins with it. When you press on the brake pedal, hydraulic pressure is exerted (by way of a pump – the master cylinder – and through metal tubes called “brake lines”) to the caliper. The caliper squeezes, or clamps down, on the rotor and stops it from spinning.
The process is similar to when you apply the brakes on a bicycle. The brake caliper on the bike holds the rubber brake pads just outside the edge of the wheel. When you squeeze the brake lever, the caliper squeezes the pads against the wheel, bringing it to a stop. Now, the caliper needs to hold the brake pads next to the rotor at all times without creating drag until the brake pedal is pushed. It is able to do this because of one or more small pistons inside the caliper that extend and retract as the hydraulic pressure increases or decreases. In other words, when you press the brake pedal, the piston extends and pushes the brake pads against the rotor. When you let go, the piston retracts and the brake pads move away from the rotor.
If the caliper ceases to function properly, one of two problems will occur. Either the pads will fail to grab the rotor, or they will fail to release it. Both cases will negatively affect performance of the brake system and need to be addressed as soon as possible. The most common brake caliper problems are hydraulic fluid leaks and seizing. Consider the following results of these problems and the effects they have on performance:
Signs Your Brake Caliper Have Gone Bad
- Premature or uneven brake pad wear. If you take your car, truck, or SUV in for routine service or inspection and find that your brake pads are wearing unevenly, or that they are wearing out before their time, one explanation is a bad brake caliper. If the caliper does not allow the brake pads to move away from the rotor, they will continue to rub and wear away even when you are not pressing on the brake pedal.
- Your vehicle pulls to one side. If you hit the brakes and your car pulls to one side or the other, a brake caliper may be responsible. This can happen in one of two ways. If the piston in a caliper becomes stuck because of debris, dirt, corrosion, or the like, it will fail to either grab or release the rotor. If it fails to grab the rotor, the car will pull away from the damaged side. If it fails to release the rotor, the car will pull towards the seized side. The latter example can occur even if you are not pressing the pedal (although it will likely increase when you do.
- You hear grinding, screeching, or rubbing noises. A stuck or seized brake caliper will often cause noises similar to those of excessively worn brake pads. But in this case, the noises can happen even when the brakes are not applied. Sometimes the sounds are due to pads that are worn down because of a seized caliper.
- Brake fluid is leaking on the ground. If you see an oily wet spot on the ground just inside one of your tires, it could be a sign that your brake system is leaking. Maybe from a caliper. If a caliper is leaking (of if any part of the brake system is leaking), the system will lose hydraulic pressure and fail. In this case, do not drive the vehicle until the leak has been repaired. Rather, have the vehicle towed to a trusted repair shop.
- You hear a clunking sound when you brake. A related, although less common, problem stems from a broken mounting bracket that holds the caliper in place. If the caliper bracket breaks, the caliper will move and make a clunking sound. As with a fluid leak, the vehicle should not be driven if a caliper bracket is damaged or broken.
If you experience any of these problems with your brake system, make sure to make an appointment with – or have your vehicle towed to – a trusted repair shop.
This article is intended only as a general guidance document and relying on its material is at your sole risk. By using this general guidance document, you agree to defend, indemnify and hold harmless Hogan & Sons Tire and Auto and its affiliates from and against any and all claims, damages, costs and expenses, including attorneys’ fees, arising from or related to your use of this guidance document. To the extent fully permissible under applicable law, Hogan & Sons Tire and Auto makes no representations or warranties of any kind, express or implied, as to the information, content, or materials included in this document. This reservation of rights is intended to be only as broad and inclusive as is permitted by the laws of your State of residence.
